Petsafe Big Dog Remote Trainer User Manual download pdf (Page 6)

10 US Customer Care Center 1-800-732-2677 www.petsafe.net 11

Transmitter Digital Display

The display stays on for approximately 30 seconds after a button press. After 30 seconds with no

button press, the display shuts off and the Transmitter goes into battery conservation mode. Pressing

any button will turn the display back on. The symbols on the display are explained below.

L indicates low stimulation levels ranging from 1-8, and appears in the lower left

corner before the battery indicator.

H indicates high stimulation levels ranging from 1-8, and appears in the lower

right corner after the battery indicator.

The battery indicator provides constant awareness of your battery’s power level.

Divided into segments, 3 indicates high battery power, 2 indicates medium, 1

indicates low (replace soon) and no bars indicate critically low (replace immediately).

Note: Red LED will ﬂash 3 times every 5 seconds to indicate low battery.

Indicates Transmitter is ready to pair with Receiver Collar. Press Stim Down (-)

button through the stimulation levels to display and begin pairing.

Transmitter LED Indicator Light – Function and Response

Button Button Function Transmitter Indicator Light Response

Tone (green) Delivers audible tone to collar Green LED on for length of button press

Stimulation

(yellow)

Delivers stimulation to collar based on

current level shown on Digital Display

(stimulation will time-out if pressed

continuously for 12 seconds or longer

and will reset after release)

Red LED on for length of button press

Note: Red LED will also ﬂash 3 times

every 5 seconds to indicate low battery.

+2 Boost (red)

Delivers stimulation at 2 levels higher

than the current setting (can not exceed

level 8 High and will also time-out after

button is held for 12 continuous seconds)

Red LED on for length of button press

Tone and

Stimulation

Buttons held

simultaneously

Transmits Pairing command to

Receiver Collar when P is visible on

Digital Display

Orange LED on for length of button press

Prepare the Receiver Collar

To Insert and Remove the Batteries

1. Remove the screws with a small

Phillips screwdriver, applying

adequate pressure for the

screwdriver head to ﬁt snugly

into the screw (2A).

2. Push the Battery Lid up

according to the arrows

stamped on the Battery Lid (2A).

3. Slide the Battery Lid out.

4. Install two (2), 3-volt batteries

positive (+) side up (2B).

Slide the Battery Lid into the

Receiver Collar.

5. Reinstall the screws (2B). Do not

over-tighten the screws.

TO REMOVE

SLIDE THEN LIFT

TO REMOVE

SLIDE THEN LIFT

Batteries

(CR2032)

Replacement batteries (3-volt, CR2032) can be found at many retailers. Contact the Customer Care

Center or visit our website at www.petsafe.net for a list of common retailers.

Risk of explosion if battery is replaced by an incorrect type. Do not short circuit, mix

old and new batteries, dispose of in fire, or expose to water. When batteries are stored

or disposed, they must be protected from shorting. Dispose of used batteries properly.

To turn Receiver Collar On

1. Press and hold the On/Off Button until the unit beeps and the Green LED light comes on.

(This takes approximately one second.)

2. Release the On/Off Button.

In normal mode, the Green LED will ﬂash once every 5 seconds, indicating the Receiver

Collar is on and ready to receive a signal from the Handheld Transmitter.

To turn Receiver Collar Off

1. Press and hold the On/Off Button until the unit beeps and the LED light shuts off. (This takes

approximately 3 seconds.)

2. Release the On/Off Button. Note: To extend the life of the batteries, turn the Receiver Collar

off when it is not in use.

Important: If the Receiver Collar is left on continuously, the maximum battery life will be

two weeks.

Step

1 2 3 4 5 6 7 8 9 10 11 ... 14 15

Comments to this Manuals

No comments

Petsafe Big Dog Remote Trainer User Manual Page 6

Comments to this Manuals

Related products and manuals for For pets Petsafe Big Dog Remote Trainer